10 GHz Carrier Class airMAX BaseStation with Dish AntennaModel: PBM10
11. Adjust the Azimuth and Elevation. Azimuth can be adjusted by rotating the antenna while supported by the stabilizer bracket. Elevation is adjusted
13. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 14. Connect the power cord to the power port on the P
Accessing airOS™Verify connectivity in the airOS Configuration Interface.1. Make sure that your host machine is connected to the LAN that is connecte
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer’s responsibility to make sure the dev
Czech RepublicThe content in this section is for exclusive use in the Czech Republic; you are instructed to look for clear channels and manually set t
SpecificationsPowerBridgeM10 RadioDimensions 170 x 250 x 53 mm (without the Feed) 170 x 250 x 272 mm (with the Feed)Weight 1.15 kg (without Feed) 1.
Safety Notices1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by the manufacturer.W
Limited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from de
DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE
NoteSome countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You
IntroductionThank you for purchasing the Ubiquiti Networks™ PowerBridge™M. This Quick Start Guide is designed to guide you through the installation, a
Industry CanadaThis Class A digital apparatus complies with Canadian ICES-003.To reduce potential radio interference to other users, the antenna type
NB-Indentification Number (if there is any)Notified body number is indicated if it is involved in the conformity assessment procedure.Please check th
EspañolLa Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junt
Declaration of ConformityČesky [Czech]UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal
Italiano [Italian]Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, è conforme ai requisiti essenziali ed alle altre dis
Installation Requirements• Adjustable wrench or one 16 mm and one 24 mm wrench• Phillips screwdriver• Shielded Category 5 (or above) cabling should
2. On the front of the Dish, use the four M4x18 Screw and Washer Assemblies to secure the Radio to the Dish.
3. Connect the Elevation Rod to the back of the Dish using a M10x25 Bolt, a M10 Washer, a M10 Spring Lock Washer, and a M10 Hex Nut. Install a M16 He
*720-00062-01*720-00062-015. Connect the Mounting Bracket to the Dish:a. Insert two M10x25 Bolts through the bottom of the Mounting Bracket and thro
6. Lift the cover on the Radio by pressing down and raising it up. Connect an Ethernet cable to the Radio and place the cover back on the Radio. Ther
8. On the front of the Dish, connect the Feed to the Radio and Dish using the four M4x12 Screw and Washer Assemblies.Note: DO NOT handle the assemble
10. Place the Pole Clamps on the other side of the pole that the Dish will be mounted on and connect them to the Mounting Bracket using M10 Washers, M
Comments to this Manuals