5 GHz Point to Point 1.0+ Gbps RadioModel: AF-5, AF-5U
8airFiber® AF-5/AF-5U Quick Start Guide2. Connect an Ethernet cable to the Data port.GPSMASTERLINKRESETOVERLOAD8X6X4X to 0.25XREMOTELOCALAUXMANAGEMEN
9airFiber ConfigurationairFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure
10airFiber® AF-5/AF-5U Quick Start Guide1. Connect an Ethernet cable from your computer to the Management port on the airFiber radio.GPSMASTERLINKRES
11airFiber Configuration5. The Main tab will appear. Click the Tools drop-down and select Link Calculator. This tool will guide you on how to best mi
12airFiber® AF-5/AF-5U Quick Start Guide9. Configure the Wireless Security: a. Select the AES Key Type, HEX or ASCII.b. For the Key field: - HEX E
13Hardware InstallationHardware InstallationThe mounting hardware of the airFiber radio can be pre-assembled before pole-mounting.Mounting Hardware Pr
14airFiber® AF-5/AF-5U Quick Start Guide3. Attach the Lower Mount Bracket to the I-Bracket using two M8x14 Serrated Flange Bolts. Ensure that the slo
15Hardware Installation4. Attach the Upper Mount Bracket with Elevation Rod to the I-Bracket using two M8x14 Serrated Flange Bolts. Note: Ensure that
16airFiber® AF-5/AF-5U Quick Start Guide5. Attach the Pole Clamps to the Mount Brackets.a. Slide the slotted hole of each Pole Clamp over one upper
17Hardware Installation6. Attach the Azimuth Support Brackets together.a. Insert the two M10x100 Carriage Bolts into the Azimuth Support Bracket tha
18airFiber® AF-5/AF-5U Quick Start GuidePole-Mounting1. Attach the Azimuth Support Brackets to the pole just beneath the area where the airFiber radi
19Hardware Installation2. Attach the mounting assembly to a pole.a. Orient the mounting assembly around the pole so it is aimed in the direction of
20airFiber® AF-5/AF-5U Quick Start Guide3. Lift the airFiber radio and align the two lower Pre-Installed M10x25 Flanged Bolts with the slots on the L
21Hardware Installation4. Align the two upper Pre-Installed M10x25 Flanged Bolts of the airFiber radio next to the slots on the Upper Mount Bracket.
22airFiber® AF-5/AF-5U Quick Start Guide5. Attach a ground wire: a. Remove the nut from the Grounding Point.b. Attach a ground wire (min. 8 AWG or
23Connecting EthernetConnecting Ethernet1. Push the button and slide the port cover down to access cableports. (The port cover cannot be completely
24airFiber® AF-5/AF-5U Quick Start Guide3. Connect the other end of the Ethernet cable from the Data port to the Ethernet port labeled POE on the Gig
25Connecting EthernetBelow is a diagram of a finished installation with recommended surge protectors installed.Ground to Pole, Tower,or Grounding Bloc
26airFiber® AF-5/AF-5U Quick Start GuideAlignmentTips• To accurately align the airFiber radios for best performance, you MUST align only one end of t
27AlignmentEstablishing a LinkAdjust the positions of the Master and the Slave to establish a link.Note: The Master must be aimed first at the Slave b
1IntroductionIntroductionThank you for purchasing the Ubiquiti Networks® airFiber® 5GHz Point-to-Point 1.0+ Gbps Radio. This Quick Start Guide is des
28airFiber® AF-5/AF-5U Quick Start Guide3. Master Visually aim the Master at the Slave. To adjust the Master's position:a. Rotate the airFiber
29Alignment6. Slave Aim the Slave at the Master to achieve the strongest signal level on the Remote LED Display of the Slave.Note: Values on the LED
30airFiber® AF-5/AF-5U Quick Start GuideThere are three methods for determining the received signal level:• LED Displays (described above)• airFiber
31SpecificationsSpecificationsairFiber AF-5/AF-5UDimensions 938.4 x 468.4 x 281.4 mm(36.94 x 18.44 x 11.08 in)WeightMount Not IncludedMount Included11
32airFiber® AF-5/AF-5U Quick Start GuideReceive SensitivitySpatial StreamsModulationSensitivity (10 MHz)Sensitivity (20 MHz)FDD Capacity*TDD Capacit
33Safety NoticesSafety Notices1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by th
34airFiber® AF-5/AF-5U Quick Start GuideLimited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder
35Limited WarrantyDisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY Data,
36airFiber® AF-5/AF-5U Quick Start GuideComplianceFCCChanges or modifications not expressly approved by the party responsible for compliance could voi
37ComplianceRF Exposure WarningThe antennas used for this transmitter must be installed to provide a separation distance of at least 126 cm (AF-5) or
2airFiber® AF-5/AF-5U Quick Start GuideHardware OverviewSideGrounding PointElevation RodHex Nut to adjust Elevation RodPre-Installed M10 x25 Flanged
38airFiber® AF-5/AF-5U Quick Start GuideDeutschDie Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/ode
39Declaration of ConformityItalianoLa direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o
40airFiber® AF-5/AF-5U Quick Start GuideJL091514Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ UBIQUITI NETWORKS ΔΗΛΩΝΕΙ ΟΤΙ UBIQUITI NETWORKS device, ΣΥΜΜΟΡΦΩΝΕΤΑΙ Π
© 2013-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, and TOUGH
3Hardware OverviewInterfacesGPSMASTERLINKRESETOVERLOAD8X6X4X TO 0.25XREMOTELOCALMANAGEMENT DATAAUXACT SPEED ACT SPEED Interface DescriptionReset Butto
4airFiber® AF-5/AF-5U Quick Start GuideLEDsGPSMASTERLINKRESETOVERLOAD8X6X4X to 0.25XREMOTELOCALAUXMANAGEMENT DATAACT SPEED ACT SPEED LED State StatusG
5Hardware OverviewLED State StatusLocal OnDisplays the received signal strength in dBm of the local airFiberradio.Overload Fast Flash Overload Condit
6airFiber® AF-5/AF-5U Quick Start GuideInstallation RequirementsPre-Assembly Tool• 13 mm wrenchPole-Mounting Tool• 17 mm wrenchOther Requirements•
7Installation OverviewInstallation OverviewWe recommend that you configure your paired airFiber radios before mounting. Below is an overview of the in
Comments to this Manuals