High-Performance Integrated InnerFeed™ airMAX® ac BridgeModel: PBE-5AC-620
10. Each M10x100 Bolt includes a flat washer, lock washer, and nut. Remove these and use them to secure the bolts when assembling. 11. Attach the Stab
12. Attach the pole-bracket assembly to the pole:a. Slide the slot of each Pole Clamp over the corresponding M8x150 CarriageBolt.b. Tighten the ser
13. Lift the Dish Reflector and align the two lower Hex Head Bolts with the slots on the Lower Pole Bracket. Seat the bolts in the slots.14. Attach ea
15. Before adjusting the tilt angle, ensure that the six Hex Head Bolts are loose enough to allow movement.IMPORTANT: If you cannot spin the washers f
Note: Steps 18-21 are optional instructions for mounting the Gigabit PoE Adapter on a wall.18. Remove the wall-mount bracket from the Gigabit PoE Adap
22. Connect the other end of the Ethernet cable from the PowerBeam to the Ethernet port labeled POE on the Gigabit PoEAdapter.23. Connect an Ethernet
Accessing airOSVerify connectivity in the airOS Configuration Interface. 1. Make sure that your host machine is connected via Ethernet to the PowerBe
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer's responsibility to make sure th
SpecificationsPowerBeam ac PBE-5AC-620Dimensions650 x 650 x 386 mm (25.6 x 25.6 x 15.2")Weight 6.4 kg (14.11 lb)Operating Frequency Worldwide: 51
Safety Notices1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by the manufacturer.W
IntroductionThank you for purchasing the Ubiquiti Networks® PowerBeam™ac. This Quick Start Guide is designed to guide you through the installation, a
Limited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from de
DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE
NoteSome countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You
This radio transmitter FCC ID: SWX-PBE5AC has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain an
Les utilisateurs devraient également noter que radars haute puissants sont alloués comme principaux utilisateurs (c’est-à-dire les utilisateurs de pri
RoHS/WEEE Compliance StatementEnglishEuropean Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging
EspañolLa Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junt
Declaration of ConformityČesky [Czech]UBIQUITI NETWORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal
Lietuviškai [Lithuanian]UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvo
Hardware OverviewBottom ViewCable DoorRear HousingTechnologyEthernet PortRelease Button SlotRelease ButtonDish ReflectorAlignment PinsReset ButtonAnte
LEDsSignal The default values (from left to right) are shown below:LED will light blue when the wireless signal strength is equal to or above -65 dBm
Installation Requirements• Phillips screwdriver• 13 mm wrench• 16 mm wrench• Shielded Category 5 (or above) cabling should be used for all wired E
3. Attach the Antenna Feed:a. Insert the Antenna Feed into the Rear Housing, and push until it locks into place with a click. b. Lightly pull the A
5. Attach two Hex Head Bolts, two Lock Washers, and two Flat Washers to the bottom of the Mounting Bracket. Ensure that there is a gap of 8 mm betwee
6. Attach the horizontal slot of the Support Arm to the Upper Pole Bracket using a Hex Head Bolt, Lock Washer, and FlatWasher.Note: Ensure that the
8. Each M8x150 Carriage Bolt includes a serrated flange nut. Remove these and use them in the next step. 9. Attach one Pole Clamp to each pole brack
Comments to this Manuals